Share:

BASIC ENGINEERING & TECHNICAL KNOWLEDGE FOR TROUBLESHOOTING OF INDUSTRIAL MACHINE CIRCUIT FAULTY

Course Introduction

In manufacturing industry , most of the Industrial machine using electrical system, electronic system , electro-mechanical system and electro-pneumatic system to operate the machine and generates the desire output according to production required. To ensure an effectiveness of support service to production or manufacture department , the technicians and engineers shall have the basic knowledge to checking , verify and perform troubleshooting of Industrial machine faulty.

OTC Training Centre Sdn Bhd provides the Technical Training program to enhance Engineers and Technicians knowledge, skill and technique related to Industrial machine repair. Basic engineering and Technical Knowledge for Troubleshooting of Industrial Machine Circuit Faulty (2 Days program) contents:

a) Theory/Quiz – Basic knowledge for engineering system – electrical, electronic and electro- mechanical

b) Theory/Quiz- Basic block diagram of electrical machine 

c) Theory/Quiz – Basic wiring diagram of electrical system single & 3 phase

d) Theory/Quiz – Basic component specification and Circuit function – Power Devices, Sensor , Control Devices and Output Devices

e) Safety Guide – Safety Precaution & Guideline for Troubleshooting of Electrical machine

f) Practical 1 – Application of Multimeters – Testing components and measurement technique.

g)Practical 2- Testing, generate test point and measurement technique

h) Practical 3- Perform electrical wiring and measurement technique of current and voltage.

i) Practical 3- Circuit analysis – Electrical machine common problems, testing and verification technique.

j) Practical 4- Wiring , Testing and Verification status of Electrical machine assembly:

– AC Supply  / AC Filter / Switching Mode Power Supply / DC Motor

– AC Supply / Solid state Relay / Battery / AC Bulb 

– AC Supply / Inverter Motor /  AC Motor

k) Practical 5 – Electrical Component Testing and Verification Technique.

– AC Filter / Switching Power Supply/ Main Circuit Breaker / ELCB

– Magnetic Contactor / AC Relay /AC Valve/AC Motor / DC Motor / Heater

– Electronic components – Fuse / Passive component/ diodes / Transistors        

 

Course content

Introduction to Basic Engineering & Technical knowledge for Troubleshooting of Industrial machine circuit faulty

  • Self rate skill & knowledge for troubleshooting of industrial machine
  • List down common machine problem in your area / production

Basic knowledge for engineering system

  • Electrical system
  • Electronic system
  • Electro mechanical system
  • Electro pneumatic system

Understanding Basic block diagram of industrial machine

  • Basic design of electrical machine

Generates basic block diagram of

  • Machine with Single Phase Motor
  • Machine with 3 Phase Motor
  • Machine with Heater Assembly

Basic wiring diagram of industrial machine

a)Single phase system

b)3 phase – Star wiring

c)3 phase – delta wiring

d)PLC System / Ladder Diagram

Practical 1

Generate test point and measurement technique based on Wiring Diagram A

a)Generate test point for voltage measurement

b)Identify High Pin (Red Probe) and Low Pin (Black Probe) for each measurement.

Safety Precaution & Guideline for Troubleshooting of industrial machine

Practical 2

 Application of Test equipment

a)Digital Multimeter

      • Continuity Test / Resistance Test / Short & Open Test
      • Capacitance Test / Diode Test
      • Measurement Voltage

Practical 3

Perform Electrical wiring and measurement technique based on Electrical Diagram B

a)Measurement of voltage & data collection

b)Measurement of current & data collection

Practical 4

Industrial machine Common Problems and Component faults.

a)Single Phase with 7 AC Motors

b)AC DC Power Supply

c)Micro controller not function

d)Inverter Motor not function

e)Heater Assembly not function

Practical 5

Wiring , Testing and  Verification circuit function of Industrial machine  System

a)Project 1

      • AC Supply /AC Filter / Switching Power Supply /DC Motor

b)Project 2

      • AC Supply / Solid state Relay / Switch / Battery /AC Bulb

c)Project 3

      • AC Supply / AC Filter /Inverter Motor / AC Motor

Practical 6

Electrical Component Testing and Verification Technique.

a)Main Circuit Breaker / ELCB

b)Magnetic Contactor / AC Relay/ Basic Controller

c)AC Filter / AC Motor / Stepper Motor

d)Electronic components

Reference

 

 

“Take the next step in your professional journey—reserve your seat today!”

By: FACE TO FACE PUBLIC PROGRAM

Download Program Brochure:

Follow Us:

Feedback Video

Program Video

How To Submit an Enquiry to Us?

  1. Fill in the form below and submit to us.
  2. Initiate a conversation via live chat on the bottom left of our website by stating: “Hi, my name is [your-name]. I’ve already submitted the form for this training.”
  3. We’ll promptly reach out to you regarding the training you’re interested in.

Program Enquiry Form

    ORGANIZATION DETAILS






    PERSON-IN-CHARGE DETAILS




    FOR FURTHER INFORMATION, PLEASE CONTACT US!